---

context isdn-in {

_X. =>          {
                Dial(SIP/11&SIP/12&SIP/13&SIP/14,15,Ttr);
                VoiceMail(11);
                Hangup();
                }
}

---

---

;
; CAPI config
;
;

; general section

[general]
nationalprefix=0        ; or for example "+49"
internationalprefix=00  ; or for example "+"
rxgain=1.0      ;linear receive gain (1.0 = no change)
txgain=1.0      ;linear transmit gain (1.0 = no change)
language=de      ;set default language

; interface sections ...

[ISDN1]
isdnmode=msn    ;'MSN' (point-to-multipoint) or 'DID' (direct inward dial)
incomingmsn=*    ;allow incoming calls to this list of MSNs/DIDs, * = any
controller=1    ;CAPI controller number of this interface/port
group=1          ;dialout group
softdtmf=on      ;enable/disable software DTMF detection, recommended for AVM cards
relaxdtmf=on    ;in addition to softdtmf, you can use relaxed DTMF detection
faxdetect=off 
faxdetecttime=0 
context=isdn-in  ;context for incoming calls
holdtype=hold    ;when the PBX puts the call on hold, ISDN HOLD will be used. If
                ;set to 'local' (default value), no hold is done and the PBX may
                ;play MOH.
echocancelold=yes;use facility selector 6 instead of correct 8 (necessary for older eicon drivers)

devices=2        ;number of concurrent calls (B-Channels) on this controller
                ;(2 makes sense for single BRI, 30/23 for PRI/T1)

---

---

[general]
context=default                ; Default context for incoming calls
;allowguest=no                  ; Allow or reject guest calls (default is yes)
allowoverlap=no                ; Disable overlap dialing support. (Default is yes)
;allowtransfer=no              ; Disable all transfers (unless enabled in peers or users)
                                ; Default is enabled
bindport=5060                  ; UDP Port to bind to (SIP standard port is 5060)
bindaddr=0.0.0.0                ; IP address to bind to (0.0.0.0 binds to all)
srvlookup=yes                  ; Enable DNS SRV lookups on outbound calls
mohinterpret=default
language=de

;Beispieltelefon
[11]
username=beispiel
secret=geheim
host=dynamic
type=friend
context=sip

---

---

[general]
language=de
callwaiting = yes
threewaycalling = yes
callwaitingcallerid = yes
transfer = yes
canpark = yes
cancallforward = yes
callreturn = yes
callgroup = 1
pickupgroup = 1

;Beispieluser
[11]
fullname = Beispieluser
hasvoicemail = yes
vmsecret = geheim
context = sip
hassip = yes
hasiax = no

---

---

[general]
context=default
bindport=5060
bindaddr=X.X.X.X
srvlookup=yes

; *******************************************************
;      SICHERHEITSASPEKTE      ANFANG                  *
; *******************************************************

alwaysauthreject=yes            ; Wir lassen abgewiesene User nicht wissen DAS $
allowguest=no                  ; Allow or reject guest calls (default is yes)

; Angeschlossene Geräte über Ihre Default IP

;deny=89.32.214.0/0.0.0.0 ; ein beispiel für den ausschluss einer ip

; *******************************************************
;      SICHERHEITSASPEKTE      ENDE                    *


; *******************************************************


register => XXX:XXX@sipgate.de/XXX
; hiermit registrieren wir den Asterisk bei Sipgate, um ankommene Anrufe
; entgegennehmen zu koennen

[3921391e0]
; dies ist der Context, den wir zum Raustelefonieren verwenden
; da dieser Context nur zum Raustelefonieren verwendet wird,
; ist die Angabe von "context =" hier ueberfluessig, da wir ja ohnehin
; aus der extensions.conf hierher kommen
;
type=peer
username=XXX
fromuser=XXX
secret=XXX
host=sipgate.de
fromdomain=sipgate.de
insecure=very
canreinvite=no
nat=no
disallow=all
allow=ulaw

[sipgate_de_in]
; das ist der Context für ankommende Anrufe
; von sipgate.de
; Diesen Context brauchen wir nur einmal -
; egal wieviele Sipgate-Accounts wir registrieren
; wichtig ist, dass dies der LETZTE Context von
; oben nach unten in der sip.conf  betrachtet, ist
; der einen Verweis auf sipgate.de beinhaltet !
; Durch die Angabe von "context = ankommend"
; der einen Verweis auf sipgate.de beinhaltet !
; Durch die Angabe von "context = ankommend"
; werden alle Anrufe in den gleichnamigen Context
; [ankommend] in der extensions.conf geleitet.
;
type=peer
fromdomain=sipgate.de
host=sipgate.de
disallow=all
allow=ulaw
context=ankommend

[30]
callerid=Phone 1 <30>
host=dynamic
domain=XXX.XXX.XXX.XXX
user=30
seccret=XXX
type=friend
mailbox=30
nat=yes
canreinvite=no

[31]
callerid=Phone 2 <31>
host=dynamic
domain=XXX.XXX.XXX.XXX
user=31
secret=XXX
type=friend
mailbox=31
nat=yes
canreinvite=no

[32]
callerid=Phone 3 <32>
host=dynamic
domain=XXX.XXX.XXX.XXX
user=32
secret=XXX
type=friend
mailbox=32
nat=yes
canreinvite=no

---

---

[general]
static=yes
writeprotect=no

; --------------------------------------------------------------------
; Es hat sich als gute Praxis erwiesen, die Inhalte der Datei
; extensions.conf modular aufzubauen. Diese Praxis wollen
; wir auch hier anwenden
;

[lokal]
; Erreichbarkeit der Nebenstellen 30-39
; untereinander herstellen

exten => _3X,1,NoCDR()
exten => _3X,n,Dial(SIP/${EXTEN},55,Ttr)

[sipgate_out]
; Diesen Context verwenden wir zum waehlen von abgehenden
; Rufnummern über den Sipgate Account XXX

exten => _0.,1,Dial(SIP/${EXTEN}@XXX,45,r)

[ankommend]
; alle Anrufe mit einer ID 3921391e0  sollen an das SIP Endgeraet 30
; signalisiert werden

exten => XXX,1,Dial(SIP/30,45,r)


; --------------------------------------------------------------------
;
; hier kommt der default-Context, in dem alle Geraete in der
; Grundkonfiguration erstmal laufen.
; Alle Geraete können sich gegenseitig anrufen

[default]
include => lokal
include => sipgate_out

---

---

root@vs1190020:~# asterisk
root@vs1190020:~# asterisk -rvvv
Asterisk 1.6.2.11, Copyright (C) 1999 - 2010 Digium, Inc. and others.
Created by Mark Spencer <markster@digium.com>
Asterisk comes with ABSOLUTELY NO WARRANTY; type 'core show warranty' for details.
This is free software, with components licensed under the GNU General Public
License version 2 and other licenses; you are welcome to redistribute it under
certain conditions. Type 'core show license' for details.
=========================================================================
  == Parsing '/etc/asterisk/asterisk.conf':  == Found
  == Parsing '/etc/asterisk/extconfig.conf':  == Found
Connected to Asterisk 1.6.2.11 currently running on vs1190020 (pid = 16251)
Verbosity was 0 and is now 3
  == Using SIP RTP CoS mark 5

---

Angehängte Dateien

chan_mobile.patch.tar.gz (5,0 KB)

---

handle_request_invite: Failed to authenticate device "test"<sip:test@IP

---

---

#!/usr/bin/perl -w

# AGI Ldap CallerId Lookup for Asterisk
# LDAP schema is mozillaAbPersonAlpha, Number format "0894711"
# use exten => s,1,AGI(ldaplookupphone.agi) in extensions.conf
#
# V 0.01 2010-09-02 Reimer Prochnow, reimerp at gmx dot net
# Credits to Matt Schmandt and duese
# use as CC-BY-SA 3.0
#
# Done in Perl as Shell is not powerful enough for parsing output

use strict;

# far too slow: use Net::LDAP;
use MIME::Base64 qw(decode_base64);
use Encode qw(decode);

$|=1;

my $agi_callerid;
my $num;
if ($#ARGV >= 0) {
    $agi_callerid=$ARGV[0];        # for test
    $num="*$agi_callerid*";        # also allow wildcards around number
} else {

# Setup some variables
my %AGI;

while(<STDIN>) {
    chomp;
    last unless length($_);
    if (/^agi_(\w+)\:\s+(.*)$/) {
        $AGI{$1} = $2;
    }
}

#print STDERR "AGI Environment Dump:\n";
#foreach my $i (sort keys %AGI) {
#    print STDERR " -- $i = $AGI{$i}\n";
#}

$agi_callerid=$AGI{'callerid'};
$num=$agi_callerid;
}

my $cn='';

my $ldapcmd="/usr/bin/ldapsearch -h server -x -D cn=asterisk,dc=xxx,dc=yyy -w ***** " .
        "-b ou=personal,dc=xxx,dc=yyy -LLL -s one " .
        "\"(&(objectClass=mozillaAbPersonAlpha)(|(homePhone=$num)(mobile=$num)(pager=$num)(telephoneNumber=$num)))\"" .
        ' | sed -n -e "H;\${g;s/\n //g;p}"';    # does unfold, not that easy in perl

open (LDAP, "$ldapcmd |") || die ("Unable to open $ldapcmd: $!");
while (<LDAP>){
    chop;
    if (/([^:]*):: (.*)/) {
        $_="$1: " . Encode::decode('utf8', decode_base64($2));  # decodes UTF-8 for :: vars
    }
    if (/^dn[^=]*=([^,]*).*/) { $cn=$1; }
    elsif (/^([^:]*): .*$agi_callerid/) { $cn.='/'.substr($1,0,3);}    # builds: "peter falk/mob"
    #elsif (/^$/) { print "$cn\n"; }
    #print "$cn\n";
}

print 'SET CALLERID "' . $cn . '"<' . $agi_callerid . '>' . "\n";
#exit 0;

---